RUTC50

5G Sub-6Ghz SA/NSA 2.4/3.4Gbps DL (4×4 MIMO), 900/550 Mbps UL (2×2); 4G (LTE) – LTE Cat 20 2.0Gbps DL, 210Mbps UL; 3G – 42 Mbps DL, 5.76Mbps UL

Release 16

2 SIM cards, auto-switch cases: weak signal, data limit, SMS limit, roaming, no network, network denied, data connection fail, SIM idle protection

Signal strength (RSSI), SINR, RSRP, RSRQ, EC/IO, RSCP, Bytes sent/received, connected band, IMSI, ICCID, SIM provider, operator, network type, cell ID, LAC, TAC, ARFCN, UARFCN, EARFCN

SMS status, SMS configuration, send/read SMS via HTTP POST/GET, EMAIL to SMS, SMS to EMAIL, SMS to HTTP, SMS to SMS, scheduled SMS, SMS autoreply, SMPP

Supports sending and reading Unstructured Supplementary Service Data messages

Operator black/white list (by country or separate operators)

Possibility to use different PDNs for multiple network access and services

Band lock, Used band status display

When working with devices with two SIM slots, the one not currently in use will remain idle until the device switches to it, meaning that no data is used on the card until then

Auto APN

Direct connection (bridge) between mobile ISP and device on LAN

Router assigns its mobile WAN IP address to another device on LAN

Framed routing: support an IP network behind 5G UE

802.11b/g/n/ac/ax (Wi-Fi 6) with data transmission rates up to 2402Mbps on 5GHz, 576Mbps on 2.4GHz (Dual Band, MU-MIMO)

WPA2-Enterprise – PEAP, WPA2-PSK, WPA-EAP, WPA-PSK, WPA3-SAE, WPA3-EAP, OWE; AES-CCMP, TKIP, Auto-cipher modes, client separation, EAP-TLS with PKCS#12 certificates, disable auto-reconnect

ESSID stealth mode

Up to 512 simultaneous connections

Wireless mesh (802.11s), fast roaming (802.11r), BSS transition management (802.11v), radio resource measurement (802.11k)

Whitelist, blacklist

Once scanned, a user will automatically enter your network without needing to input login information.

1 x WAN port 10/100/1000 Mbps, compliance with IEEE 802.3, IEEE 802.3u, 802.3az standards, supports auto MDI/MDIX crossover

4 x LAN ports, 10/100/1000 Mbps, compliance with IEEE 802.3, IEEE 802.3u, 802.3az standards, supports auto MDI/MDIX crossover

Static routing, Dynamic routing (BGP, OSPF v2, RIP v1/v2, EIGRP, NHRP), Policy based routing

TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, SFTP, FTP, SMTP, SSL/TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet, SMPP, SNMP, MQTT, Wake On Lan (WOL)

H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets

Ping Reboot, Wget Reboot, Periodic Reboot, LCP and ICMP for link inspection

Port forward, traffic rules, custom rules

View all your Firewall statistics, rules, and rule counters

View device ports, enable and disable each of them, turn auto-configuration on or off, change their transmission speed, and so on

Visual representation of your network, showing which devices are connected to which other devices

Static and dynamic IP allocation, DHCP relay, DHCP server configuration, status, static leases: MAC with wildcards

Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e

Supported >25 service providers, others can be configured manually

Wi-Fi WAN, Mobile, VRRP, Wired options, each of which can be used as an automatic Failover

Balance Internet traffic over multiple WAN connections

Captive portal (hotspot), internal/external Radius server, Radius MAC authentication, SMS authorisation, internal/external landing page, walled garden, user scripts, URL parameters, user groups, individual user or group limitations, user management, 9 default customisable themes and optionality to upload and download customised hotspot themes

Possibility to mount remote file system via SSH protocol

Pre-shared key, digital certificates, X.509 certificates, TACACS+, Radius, IP & login attempts block, time-based login blocking, built-in random password generator

Pre-configured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI; DMZ; NAT; NAT-T

DDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks)

Port and tag-based VLAN separation

Mobile data limit, customizable period, start time, warning limit, phone number

Blacklist for blocking out unwanted websites, Whitelist for specifying allowed sites only

Flexible access control of SSH, Web interface, CLI and Telnet

Multiple clients and a server can run simultaneously, 27 encryption methods

DES-CBC 64, RC2-CBC 128, DES-EDE-CBC 128, DES-EDE3-CBC 192, DESX-CBC 192,

BF-CBC 128, RC2-40-CBC 40, CAST5-CBC 128, RC2-64-CBC 64, AES-128-CBC 128, AES-128-CFB 128, AES-128-CFB1 128, AES-128-CFB8 128, AES-128-OFB 128, AES-128-GCM 128, AES-192-CFB 192, AES-192-CFB1 192, AES-192-CFB8 192, AES-192-OFB 192, AES-192-CBC 192, AES-192-GCM 192, AES-256-GCM 256, AES-256-CFB 256, AES-256-CFB1 256, AES-256-CFB8 256, AES-256-OFB 256, AES-256-CBC 256

IKEv1, IKEv2, with 14 encryption methods for IPsec (3DES, DES, AES128, AES192, AES256, AES128GCM8, AES192GCM8, AES256GCM8, AES128GCM12, AES192GCM12, AES256GCM12, AES128GCM16, AES192GCM16, AES256GCM16)

GRE tunnel, GRE tunnel over IPsec support

Client/Server instances can run simultaneously, L2TPv3, L2TP over IPsec support

Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the program’s code

Method of building scalable IPsec VPNs

SSTP client instance support

ZeroTier VPN client support

WireGuard VPN client and server support

Tinc offers encryption, authentication and compression in it’s tunnels. Client and server support.

Tailscale offers speed, stability, and simplicity over traditional VPNs. Encrypted point-to-point connections using the open source WireGuard protocol

Client, Server

TCP

Server, Client

TCP, USB

MODBUS TCP custom register block requests, which read/write to a file inside the router, and can be used to extend MODBUS TCP Client functionality

8-bit: INT, UINT; 16-bit: INT, UINT (MSB or LSB first); 32-bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII

HTTP(S), MQTT, Azure MQTT, Kinesis

Extract parameters from multiple sources and different protocols, and send them all to a single server

Allows sending commands and receiving data from MODBUS Server through MQTT broker

Station, Outstation

TCP

DLMS – standard protocol for utility meter data exchange

Client

TCP, USB

Permite monitorear: Datos del dispositivo, Datos móviles, Información de red, Disponibilidad

Permite monitorear: tipo de WAN, IP de WAN, nombre del operador móvil, intensidad de la señal móvil, tipo de red móvil

Permite monitorear: Modelo de dispositivo, Revisión y Número de serie, Tipo de WAN e IP, ID de celda móvil, ICCID, IMEI, Tipo de conexión, Operador, Intensidad de señal

Puede enviar la dirección IP del dispositivo, la cantidad de bytes enviados/recibidos, la temperatura, el recuento de PIN al servidor de Azure IoT Hub, el estado de la conexión móvil, el estado del vínculo de red, IMEI, ICCID, el modelo, el fabricante, la serie, la revisión, IMSI, el estado de la SIM, el estado del PIN, la señal GSM, WCDMA RSCP, WCDMA EC/IO, LTE RSRP, LTE SINR, LTE RSRQ, CELL ID, operador, número de operador, tipo de conexión

Mediatek, doble núcleo, 1,3 GHz, ARM Cortex A53

512 MB DDR3

Memoria flash NOR en serie de 16 MB, memoria flash NAND en serie de 512 MB

Actualizar FW desde archivo, verificar FW en servidor, perfiles de configuración, copia de seguridad de configuración

Actualizar FW

Actualizar el firmware/configuración de varios dispositivos a la vez

Actualizar FW sin perder la configuración actual

Un restablecimiento completo de fábrica restaura todas las configuraciones del sistema, incluida la dirección IP, el PIN y los datos del usuario a la configuración predeterminada del fabricante.

RutOS (sistema operativo Linux basado en OpenWrt)

Busybox, Lua, C, C++

Paquete SDK con entorno de compilación proporcionado

Puede crear su propio firmware personalizado y su propia aplicación de página web cambiando colores, logotipos y otros elementos en nuestro firmware para adaptarlo a sus necesidades o las de sus clientes.

GPS, GLONASS, BeiDou, Galileo y QZSS

Coordenadas GNSS a través de WebUI, SMS, TAVL, RMS

NMEA 0183

Protocolo NTRIP (Transporte en red de RTCM a través del protocolo de Internet)

Software de servidor compatible TAVL, RMS

Zonas de geocerca múltiples configurables

USB 2.0

Compartir Samba, USB a serie

Posibilidad de conectar HDD externo, pendrive, módem adicional, impresora, adaptador USB-serie

FAT, FAT32, exFAT, NTFS (solo lectura), ext2, ext3, ext4

1 x entrada digital, 0 – 6 V detectados como lógica baja, 8 – 50 V detectados como lógica alta

1 x salida digital, salida de colector abierto, salida máxima 50 V, 300 mA

Correo electrónico, RMS, SMS

Permite establecer ciertas condiciones de E/S para iniciar el evento.

Toma de corriente CC industrial de 4 pines

9 – 50 VCC, protección contra polaridad inversa, protección contra sobretensiones/transitorios

Posibilidad de alimentación a través del puerto LAN1, no compatible con estándares IEEE802.3af, 802.3at y 802.3bt, Modo B, 9 – 30 VDC

Inactivo: < 4,5 W, Máx.: < 13,5 W

5 puertos RJ45, 10/100/1000 Mbps

1 x entrada digital, 1 x salida digital en conector de alimentación de 4 pines

4 LED de estado de WAN, 3 x tipo de conexión móvil, 3 x intensidad de conexión móvil, 8 x estado de LAN, 1 x energía, 2 x Wi-Fi 2.4G y 5G, 2 x estado de WAN

2 ranuras para SIM (Mini SIM – 2FF), 1,8 V/3 V, soportes para SIM externos, eSIM (opcional)

1 conector de alimentación de 4 pines

4 x SMA para móviles, 3 x RP-SMA para Wi-Fi, 1 x SMA para GNSS

1 puerto USB A para dispositivos externos

Botón Reiniciar/Restablecer valores predeterminados del usuario/Restablecer valores de fábrica

1 x tornillo de puesta a tierra

Carcasa y paneles de aluminio anodizado.

130,4 x 42,6 x 103,4 mm

452 gramos

Riel DIN, montaje en pared, superficie plana (todos requieren un kit adicional)

-40 °C a 75 °C

10% a 90% sin condensación

IP30